Search results for "Chromate conversion coating"

2017

Abstract Chromic acid anodizing is important for the corrosion protection of aerospace aluminium alloys. Previous study has demonstrated that SO 4 2 − impurity in the chromic acid affects the film growth on aluminium at a voltage of 100 V. The present work further investigates aluminium and extends the study to industrial anodizing conditions (Bengough-Stuart (B-S) process) and to the AA 2024-T3 alloy. It is shown that SO 4 2 − concentrations between ~ 38–300 ppm reduce the film growth rate for aluminium anodized at 100 V in comparison with an electrolyte than contains ≤ 1.5 ppm SO 4 2 − , whereas ~ 1500–3000 ppm SO 4 2 have an opposite effect and lead to an unstable pore diameter. Under th…

Study of the Chemical Conversion of Aluminum Alloys by Coupling CFDE and EQCM

2004

The ability of the channel flow double electrode (CFDE) technique and electrochemical quartz crystal microbalance (EQCM) for studying in situ chromate phosphate conversion coating on 5182 aluminum alloys was explored. It was first demonstrated that aqueous Cr(VI) can be analyzed quantitatively with the CFDE technique by reduction into Cr(III) on a graphite electrode. Samples used for EQCM were quartz plated by physical vapor deposition using a 5182 alloy target, allowing thin layers of aluminum alloys with a similar chemical composition to be obtained. EQCM was adapted in order to account for the hydrodynamic conditions in an industrial process, by placing the quartz in a flow cell. In orde…

Structural Analysis and Photocurrent Spectroscopy of CCCs on 99.99% Aluminum

2003

A characterization of chromate conversion coatings (CCCs) formed in the presence and in the absence of accelerator (ferroferricyanide redox couple) has been performed by various techniques (transmission electron microscopy, TEM, glow discharge optical emission spectrometry, GDOES, X-ray absorption near-end structure, XANES, and photon correlation spectroscopy). The results of a detailed investigation on morphological, compositional, and solid-state properties of freshly converted aluminum samples at different immersion times (30 s-90 min) are reported. The TEM and GDOES data suggest the presence of iron-cyanide species only in the external layer of CCC of nearly constant thickness. The XANE…

Improvement of the electrochemical behaviour of Zn-electroplated steel using regenerated Cr(III) passivation baths

2014

[EN] Conversion coatings based on trivalent chromium are more sensitive to the presence of zinc and iron impurities than the chromate formulations. This fact contributes to a decrease in the quality of passivation and to the generation of a significant amount of hazardous liquid waste. Recently, a new eco-innovative process based on Emulsion Pertraction Technology (EPT) is being implemented at industrial scale for selectively removing Zn and Fe from spent passivation baths in order to enhance the lifetime of the Cr (III) baths. In this study, the effect of Zn and Fe removal on the electrochemical behaviour of Zn-electroplated steel samples was evaluated by means of polarisation curves and e…

Two-Dimensional Assembling of (2,2‘-Bipyrimidine)bis(oxalato)chromate(III) Units through Alkaline Cations

1999

Self-assembling of the tris-chelated [Cr(bpm)(ox)2]- complex with Na+ in aqueous solution leads to the remarkable bimetallic honeycomb layered compound of formula [NaICrIII(bpm)(ox)2]·5H2O (2) (bpm...

Magnetic and magneto-optical properties of nickel hexacyanoferrate/chromate thin films

2017

One of the most important challenges of modern science and technology is the quest for novel and tuneable materials, the properties of which can be widely controlled by chemical modifications or external stimuli. Simultaneously, an interest in the development of magnetic thin films also gains significant attention. In the current paper we bring together both these challenges and present a study of a new type of low-dimensional nickel hexacyanoferrate/chromate system. Thin films were obtained by the "layer by layer" deposition technique, where the ratio of Fe/Cr was controlled by the dipping sequence. The scope of this work is a comprehensive analysis of structural, spectroscopic and magneti…

The generalized H-point standard-additions method to determine analytes present in two different chemical forms in unknown matrix samples. Part II. C…

2000

The generalized H-point standard-additions method (GHPSAM) is used in order to obtain the total Cr(VI) and chromate concentration in water samples whose matrices are completely unknown. Moreover, a new methodology, which is a modification of the GHPSAM, is proposed for the simultaneous determination of the two major chemical forms of Cr(VI) present in the sample. The method is based on the location of spectral intervals where the behaviour of the interferent absorbance can be considered as linear. From these intervals, the analyte concentration free from bias error can be estimated. Spiked samples of dig and harbour water measured in the UV–visible spectral region have been tested to check …

Bis(oxalato)chromium(III) complexes: Versatile tectons in designing heterometallic coordination compounds

2011

Abstract The mononuclear oxalato-containing chromium(III) complexes of general formula [Cr(AA)(C2O4)2]− (AA = α-diimine type ligand) are able to produce a large variety of heterometallic complexes by acting as ligands towards either fully solvated metal ions or preformed cationic complexes with available coordination sites. This review focuses on the structural diversity of the polynuclear complexes (oligonuclear and coordination polymers) which are generated by the bis(oxalato)chromate(III) species, with a special emphasis to their magnetic properties.

An ESCA and Mössbauer study of the oxide layer formed on steel in water containing chromate and chloride ions

1983

Abstract The formation of oxidic layers on steel in chromate solutions was studied by photo-electron and Mossbauer spectroscopy. To simulate more aggressive realistic systems, some chloride ions were added to the solution. The layers formed under these conditions were found to be thicker by an order of magnitude than those formed in the absence of chloride ions. They probably consist of ferric and chromic oxides of the corundum type (Fe 1−2 Cr x ) 2 O 3 , with the Cr : Fe ratio being depth dependent. The oxide layer is subdivided into small regions behaving superparamagnetically. This heterogeneity of the layer is ascribed to the attack by the chloride ions. The structure of the oxides foun…

Speciation of Cr in Leachates of a MSWI Bottom Ash Landfill

1998

Cr concentrations and speciation were determined in leachate from a municipal solid waste incinerator bottom ash landfill both experimentally and by thermodynamic model calculations. Total dissolved Cr concentrations of 0.2 mmol L-1 were determined by GFAAS. Two orders of magnitude lower values were determined upon preconcentration by an in-situ solid-phase extraction technique based on the 8-HQ cation exchanger that is specific for Cr(III) but unspecific for Cr(VI). This suggests that chromate dominates the dissolved Cr concentrations in the leachates but was up to 5 orders of magnitude undersaturated with respect to the solubility of CaCrO4 or BaCrO4. Chromate adsorption by oxyhydroxides …